New photos are up! I have added a slide show to the blog. These featured pots were all made within the last three years. They are fired to approximately cone 10 in a gas kiln with a fairly light reduction atmosphere. They are glazed with layers of ash glazes and other glazes to create this fluid characteristic that I have been interested in. I am inspired by the suggestion of nature created by the combinations and textures of the glazes. This is my jumping off point to my current exploration into salt and soda firing. As a lifelong resident of North Carolina, I am intrigued by NC's heritage in pottery. These traditional potters often used salt in their kilns combined with alkaline glazes (ash glazes). I feel it is important to preserve this tradition, while I also intend to combine this style with my own, slightly more modern approach. When the kiln is complete I will post pictures with the results as we fire it!
Friday, February 13, 2009
Thursday, February 05, 2009
Sorry folks! I have not been to the blog spot in awhile! I still have not finished the salt kiln, but instead, I have been working on a very important project. I have photo documented a day in the process of this project. The pictures below are pictures of me raku firing, a fascinating approach to firing pottery. Keep reading!
the kiln open with coasters inside
removing the coasters from the kiln
making it "crackle"
making it "crackle"
For the last few months I have been working on a project for the West District 4-H Leaders Association. I was commissioned to make coasters to be given out at the NC Volunteers Leaders Association Conference. I fired them by a process called Raku. This in an ancient traditional Japanese means of firing. For more information on this process and its fascinating history see http://en.wikipedia.org/wiki/Raku_ware
To begin, the pots, or in this case, the tiles, are made, allowed to dry, and bisque fired in an electric kiln to about 1650F degrees. The clay is now hard enough to handle, but still porous. I am ready to apply the glaze. Each piece is hand decorated. My approach to decoration is to mask off the design. I use pinstriping tape (for automobiles!). I brush the glaze over top of the design and anywhere I want the glaze to appear. Once the glaze dries, I remove the tape from the pot and the negative shapes create a pattern; in this case, the clover, the symbol of 4-H worldwide.
Now I am ready to fire. Each piece is fired individually in a small kiln called a raku kiln. The first picture is of the raku kiln with the coasters on top waiting to be fired. Notice the orange glow of the atmosphere inside. There are three to five coasters firing at once. It takes about 45 minutes for the the kiln to reach a temperature. The kiln is rigged on a pulley system to make it easier to raise the basket and retrieve the coasters from inside. Once the kiln reaches 1850F and while the coaster is still red hot, I pull them, one at a time, from the kiln using long tongs and fireproof gloves. The coaster is then transferred to a metal trashcan. The trashcan is packed with newspaper, a combustible material. Once the coaster is placed in the trashcan, the newspapers instantly burst into flames. I place more newspapers on top of the coaster and replace the lid. This process creates heavy smoke and an atmosphere void of oxygen. This atmosphere, called "reduction", creates the natural black color of the claybody.
The glazes I use are called crackle glazes. After a few moments, I use the tongs to pull the coaster back out of the trashcan. I bring the coaster close to my face and blow on it and I can hear the crackling and pinging of the glaze while the crackle effect is being achieved. I place the coaster back in the trashcan, again loaded with newspaper and wait for the paper to ignite. I replace the lid. Sometimes I repeat this process up to three times depending on how much crackling I would like to have on a certain piece. Meanwhile I have more coasters in the kiln slowly warming in the kiln, waiting for their turn. Then the process starts again!
Thanks for reading. Come back and visit soon!
I hope to have the salt/soda kiln finished before Spring.